logo
Up to 5 files, each 10M size is supported. OK
JINAN HOWOSTAR AUTO PARTS CO.,LTD 86--15098764769 fionaloveschina@gmail.com
News Get a Quote
Home - News - HOWO Brake Lining, Brake Chamber and Brake Adjuster Service Guide for Hot and Dusty Middle East Routes

HOWO Brake Lining, Brake Chamber and Brake Adjuster Service Guide for Hot and Dusty Middle East Routes

November 16, 2026

 In desert and Sahel service, HOWO and Shacman brakes rarely fail because the lining is too thin — they fail because heat and dust distort the geometry of the system around it. A drum that has been through repeated 300 °C cycles no longer fits a new lining, a slack adjuster packed with dust stops adjusting, and a brake chamber with a perished diaphragm releases slowly on a downhill grade. The lining is the cheapest part of the repair and the last thing to diagnose.

HOWO brake adjuster (WG9100440005 series) — the component most often blamed for a brake problem it did not cause.

Heat fade and dust: two different problems

Heat fade appears on loaded tippers descending long grades at 45 °C ambient: pedal travel grows, retardation drops, and the drum turns blue. Lining formulation matters here — a resin that outgasses at 280 °C will glaze and lose friction long before the friction material is worn out. Dust does the opposite: abrasive grit between lining and drum machines both surfaces, and the same grit enters the slack adjuster worm and the chamber breather, so the brakes stop releasing cleanly. Fixing one without the other is why fleets in Riyadh, Jeddah, Cairo and Khartoum report repeat brake complaints.

HOWO brake part references

Component Reference Note for hot / dusty service
Brake lining, 6 holes WG9100440027 / WG9100440026 Hole pattern improves heat dissipation; inspect for glazing at every 20,000 km
Brake lining, 8 holes WG9100440029 / WG9100440028 Higher ventilation for sustained downhill work
Brake lining, 12 holes 12-hole HOWO lining series Preferred on heavy tippers where drum temperature is the limiting factor
Brake chamber assy WG9000360600 / WG9000360900 HC16 and AC16 axles; replace diaphragm at first sign of slow release
Brake adjuster (slack adjuster) WG9100440005, WG9100340056, WG9100340060 / WG9231340060 Grease every 10,000 km in dust; a dry worm seizes without warning
Rivets WG9231340068 / 189000340068, 17*10*22 aluminium Match rivet length to lining thickness — short rivets crack linings
Air compressor VG1034130019 Shacman and HOWO; oil carry-over contaminates valves downstream
Wheel rim WG9100610065 / DZ93259619016, 9.00–22.5 Check rim/hub face runout when brakes pull to one side

Workshop sequence that stops repeat failures

  1. Measure drum diameter and out-of-round before fitting new lining. An oval drum will destroy a new lining within 10,000 km.
  2. Replace linings axle-set, not wheel-set. Mixed friction on one axle causes pull and premature wear.
  3. Inspect the slack adjuster stroke and free play after every lining change; record the pushrod stroke so the next service has a baseline.
  4. Check chamber diaphragms for cracks and the breather for dust ingress; a blocked breather holds pressure and drags the brake.
  5. Clean and grease the S-cam bushings — dry bushings are the most common hidden cause of poor return.
  6. Test on a grade, loaded, not in the yard. Heat fade only appears under sustained retardation.

Stock that reaches the workshop intact

Jinan Howostar Auto Parts Co., Ltd (HOWOSTAR) has focused on Sinotruk HOWO, Shacman and FUWA trailer parts since 2010. Founded in Jinan, Shandong — the base of the Sinotruk supply chain — the company runs a 50–100 person operation with 80–90 % of sales exported, and stocks brake linings, chambers, slack adjusters, rivets and air compressors alongside filters, oil seals and cooling parts so a fleet can rebuild an axle set in one shipment. Cartons carry the HOWOSTAR part number next to the original HOWO reference; the packing list is cross-referenced so a storeman in Mombasa or Jebel Ali can match parts without opening every box.

FAQ

How long should HOWO brake lining last in desert service? Front axle lining typically 60,000–80,000 km, rear axle 40,000–60,000 km on loaded tippers; heat exposure shortens that far more than mileage does.

Automatic or manual slack adjuster? Automatic adjusters reduce maintenance but seize when dust enters the worm. In very dusty operations, manual adjusters with a disciplined greasing routine are often more reliable.

Can I fit 12-hole lining where 6-hole was fitted? Only where the drum and rivet pattern match; check the drum part number before switching hole patterns.